Vehicles
42 not categorized PORSCHE 911 EURO SPECCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.NLA05010 Made in europe to original okrasa specs replaces 36905010 369-05-010
$369.60
Make a selection 96437505580 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Be sure to swap yours out during the next service. Sold individually. Central fitment into the transmission carrier bracket. 1 qty. Required. Tech tip: tech tip: the bushing should be mounted with the 2 openings on the vertical plane. Now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 964 rs 1 qty. Hex head...(choose a part on the right to read more) View/Change Diagram
$148.50
Make a selection 4A0949101
View/Change Diagram
From $12.00
Make a selection 170111047 This stainless-steel exhaust tip offers a period correct, timeless design with a larger diameter. It fills out the bumper cut out nicely and is manufactured in europe. Specifications: rolled lip. Polished finish. 4 (102 mm) round to fill in the entire bumper cut out. Weight: .79 kg (1.74 lbs.) sold individually. 1 necessary per car.
$141.90
Make a selection 94410301526 Smoking, sluggish, low compression engines usually have bad pistons and rings to blame for their anemic condition. Rebuild your engine properly with the finest parts available (original equip., kolbenschmidt or mahle). Do not accept imitation or aftermarket pistons. Do it once! Do it right! If you are looking for a little extra hp and torque with your rebuild, try a set of higher compression European specpistons and get performance and factory reliability. View/Change Diagram
$573.53
Make a selection 10010303808 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. However, this kit cannot be used with original cams, it requires a more aggressive cam (maximum valve lift (tdc) of 2.1 mm) and has very deep pockets for use with rsr valves. The 109-mm size means that the housings must be modified on non rennsport models. If you have a European rennsport model, these would be slip fit. This kit also requires the larger o-ring seals, part # 96410440180 and larger base gaskets, part # FVD116929. Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resi...(choose a part on the right to read more)
$12,139.99
Make a selection 94410309157 Smoking, sluggish, low compression engines usually have bad pistons and rings to blame for their anemic condition. Rebuild your engine properly with the finest parts available (original equip., kolbenschmidt or mahle). Do not accept imitation or aftermarket pistons. Do it once! Do it right! If you are looking for a little extra hp and torque with your rebuild, try a set of higher compression European spec pistons and get performance and factory reliability. View/Change Diagram
$620.96
Make a selection 94410309900
View/Change Diagram
$462.56
Make a selection 94411608001 For all cars running the single mass flywheel and European rs models. Use with guide tube part # 100105292 for Porsche 993 rs and Porsche 996 GT3 part fits only for clubsport and cup type with lightweight rs flywheel . Fits: 964rs / 968 -95 / 993rs + 996 GT3 and 997 GT3 only for clubsport version (m003) please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $198.65
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |